Troubleshooting Guide: Oculus Blinking Red Light On The Headset



If you’re an Oculus user and experiencing a blinking red light on your headset, it can be frustrating and worrisome.

However, there are several simple steps you can take to resolve this issue and get your Oculus headset back up and running smoothly.

In this troubleshooting guide, we will walk you through the common causes of the blinking red light and provide you with practical solutions to fix it.

Oculus Blinking Red Light On The Headset: Fixed

The working solutions for fixing the Oculus blinking red light issue are:

  • Do a forced charge
  • Remove cover from the lenses
  • Use a different charger
  • Use a different charging cable
  • Check the headset charging port
  • Check the power plug
  • Rule out overheating issues

Do a Forced Charge

One of the first things you can try is to perform a forced charge on your Oculus headset. Connect it to the charger and hold the power button for 30 seconds.

Then, leave it on the charger for another 30 minutes. Check if the battery meter on the screen shows an orange light, indicating that the headset is charging. Wait for the light to turn green, indicating a full charge.

Remove Cover from the Lenses

Sometimes, the Oculus Quest headset wakes up due to the writing on the black cover, draining the battery and causing a flashing red light.

Make sure to remove any cover or protective film from the lenses before using or charging the headset.

Use a Different Charger and Charging Cable

Incompatible or faulty chargers and charging cables can also cause the red blinking light issue. Try using a different charger and cable to charge your Oculus headset and see if the problem persists.

Check the Headset Charging Port

Ensure that the USB cable is correctly connected to the headset’s charging port. Plug the cable firmly and slightly lift the bottom attached to it.

You should hear a cracking noise when the cable is securely plugged in. If the issue persists, apply gentle pressure on the charging cable near the charging port.

Check the Power Plug

If the blinking red light continues, it’s possible that the power socket itself is faulty and not supplying enough power to the Oculus Quest. Try plugging the charger into another power plug and check if the orange light appears on the headset.

Rule Out Overheating Issues

Overheating can also cause the Oculus headset to flash a red light. If this is the case, the device will eventually start charging once it cools down. Make sure to give your headset enough time to cool down before attempting to charge it again.

Red blinking light issue on Quest 2 headset

If you’re facing the problem of a red blinking light on your Quest 2 headset and it’s not charging, there could be a few possible explanations.

  1. Unresponsive Charging Cord: The issue might be with your charging cord, which the Quest 2 doesn’t recognize. Solution: Try using a new charging cord.
  2. Drained Battery: If the battery is severely drained, you may need to leave it on charge for a while to recharge.
  3. Damaged Charging Port or Battery: It’s possible that the charging port or battery is damaged, requiring you to reach out to support for assistance.

Before trying the third solution, you can attempt the following troubleshooting step:

  1. Reset the Headset: If you plug in the headset and it displays a red light for a minute or two before starting to blink, it could be a software glitch. Solution: Hold down the power button for 20 seconds while the headset is plugged in.

This method has proven effective for some users as it resets the headset. In some cases, the battery level could be at 100% even though it shows 0% with the red blinking light. After holding down the power button for 20 seconds, the light should turn green, indicating a full charge.


Dealing with a blinking red light on your Oculus headset can be resolved by following these troubleshooting steps.

From performing a forced charge to checking the charging port and power plug, these solutions can help you get your Oculus headset back to normal functioning. Remember to use compatible chargers and cables, remove any lens covers, and ensure proper cooling to avoid future issues.

If the problem persists, it’s recommended to contact Oculus support for further assistance.